期刊问答网 论文发表 期刊发表 期刊问答

机械论文英文怎么写

  • 回答数

    3

  • 浏览数

    148

tree_ccb
首页 > 期刊问答网 > 期刊问答 > 机械论文英文怎么写

3个回答 默认排序1
  • 默认排序
  • 按时间排序

江南雪地

已采纳
Calculation of thermodynamic calculation is the basis of the General the calculation of the compressor in heat-aided design systems have a compressor to help would greatly speed up the design process so that a more rational Compressor lubricating oil and has no thermodynamic calculation, the calculation in manual access map errors, data are not consistent with the calculation of the selected request, the result of incorrect calculations or At present there is no response to any oil-lubricated compressor-assisted calculation By the calculation of the required number of charts, prepared without oil lubricated compressor Thermodynamics-aided design system, simplifies the success of any oil-lubricated compressor thermodynamic calculation process, the realization of the data required to calculate the line selection, Chaturvedi smart look-up table, the output of data, save and print, and to improve the accuracy of the calculation parameters and Key words thermal calculation compressor oil-free-aided design system希望能帮到你

机械论文英文怎么写

190 评论(9)

化样年华

Pressure Vessel design of the chemical industry that is a kind of mechanical design, in order to meet the needs of social life, the constant pressure vessel development and In order to production needs, the structure of the pressure vessel, the design of the way, bringing them in line with customer demand factory, the design of the following: First, pressure vessels of the board of the design; two, shell hole size, location of the design; 3 , Welding technology of This paper reviews the new type of highly efficient heat exchangers at home and abroad in recent years for the Research, Design and in accordance with national standards of shell-and-a heat exchanger, found problems in the design and through, choose the right parts, on the basis of knowledge of Shell heat exchanger to improve the views, but also at home and abroad enhanced heat transfer components and a new highly efficient heat transfer technology direction of development were Key words:(关键词:) mechanical design, heat exchangers, heat transfer enhancement, head, flange, Baffled, the national standard希望我的翻译对你有帮助
161 评论(8)

刘畅

管道支吊架 Pipe Supports and H1 管架零部件 Attachment of Support管托 shoe管卡 clampU形夹(卡) clevis锻制U形夹 forged steel clevis支耳;吊耳 lug; ear耳轴 trunnion止动挡块 shear lug托座 stool托架 cradle带状卡 strap clamp夹板,导向板 cleat可调夹板 adjustable cleat角板;连接板 gusset筋;肋 rib支承环 ring加强板 stiffiener底板 base plate顶板 top plate翅片式导向板 fin预埋件 embedded part; inserted plate垫板(安装垫平用) shim锚固件;生根件 clip预焊件(设备上) clip (on equipment)聚四氟乙烯滑动板 PTFE sliding plate连接板 tie plate连接杆 tie rod限制杆 limit rod带环头拉杆 eye rod连接杆 connecting rod杠杆 lever支撑杆 strut定位块 preset pieces间隔管(片、块) spacer滑动吊板(吊架顶部用) sliding traveler(for hanger)滑轮组 tackle-block钢索,电缆 cable木块 wood block鞍座 saddle裙座 skirt软管卷盘(简) hose reel管部附着件 pipe 2 管支架型式 Type of Pipe Support支承架 resting support滑动架 sliding support固定架 anchor导向架 guide限制性支架;约束 restraint限位架 stop限位器 stopper定值限位架 limit stop二维限位架 two-axis stop往复定值限位架 double-acting limit stop定向限位架 directional stop吊架 hanger弹簧架 spring support弹簧托架 resting type spring support弹簧吊架 spring hanger恒力吊架 constant hanger重锤式吊架 counter weight hanger弹簧恒力吊架 spring constant hanger弹簧恒力托架 resting type spring constant support滚动支架 rolling support弹簧支撑架 spring bracing减振器 snubber液压减振器 hydraulic snubber减振装置 damping device缓冲简(器) dash pot刚性吊架 rigid 3 标准及通用型支架标准管架 standard pipe support通用管架 typical pipe support悬臂架 cantilever support三角架 triangular support’支腿 legⅡ形管架 Ⅱ-type supportL形管架 L-type support柱式管架 pole type support墙架 support on wall可调支架 adjustable support管墩,低管架 sleeper特殊管架 special support管道支吊架图 piping support 4 管架安装背至背 back to back钻孔 drill长孔 slot; slot hole放气孔;通气孔 vent hole灌浆;水泥砂浆填平 grouting组装;装配 assembly攻螺孔 apping自由滑动 free to slide跨度 span对中心;找正 alignment切割使适合 cut to suit修饰使适合 trim to suit伸出长度(指预埋螺栓) extrusion液压试验中,对试验液体要求是:试验液体一般采用水,需要时也可采用不会导致发生危险的其它液体。试验时液体的温度应低于其闪点或沸点。奥氏体不锈钢制容器用水进行液压试验后应将水渍去除干净。当无法达到这一要求时,应控制水的氯离子含量不超过25mmg/L试验温度:1. 碳素钢、16MnR和正火15MnVR钢制压力容器液压试验时,液体温度不得低于5℃,其它低合金钢制容器液压试验时液体温度不得低于15℃。如果由于板厚等原因造成材料延性转变温度升高,则需相应提高试验液体温度。2. 其它钢种制容器液压试验温度按图样规定。
207 评论(14)

相关问答